Peek-a-Hide Replacement Hardware – Raspberry Pi, Camera, SD Card, or Device Enclosure

Already own a Peek-a-Hide and need to replace a component? This listing offers individual replacement hardware so you can get back up and running without purchasing a full unit.

📦 Available Options

Select the option that fits your situation:

🔹 Wide-Angle Night Vision Camera Module Only

A replacement wide-angle night vision camera module.

Best if:

• Your camera failed or was damaged
• Your Pi is still functioning and only the camera needs replacing

Includes:

• Wide-angle night vision camera module

🔹 Pi/Camera Enclosure Only

The 3D-printed enclosure that houses the Raspberry Pi and camera module and mounts to the hide.

Best if:

• Your device enclosure was cracked, broken, or lost
• You need a replacement mount for your existing electronics

Includes:

• 3D-printed Pi/camera enclosure

🔹 Raspberry Pi Zero 2 W + Camera (Fully Configured)

The complete electronics assembly, including Pi and wide-angle night vision camera, ready to reinstall into your existing housing.

Best if:

• You need a complete electronics replacement

Includes:

• Raspberry Pi Zero 2 W, conformal coated with heatsink installed
• Wide-angle night vision camera module with CSI ribbon
• 16GB microSD card, preconfigured

🔹 Raspberry Pi Zero 2 W Only (No SD Card)

The Raspberry Pi Zero 2 W prepared and treated without an SD card.

Best if:

• Your Pi failed or was damaged and you already have a working SD card
• You want to reuse your existing SD card

Includes:

• Raspberry Pi Zero 2 W, conformal coated with heatsink installed

🔹 Raspberry Pi Zero 2 W Only (Fully Configured)

The Raspberry Pi Zero 2 W with microSD card installed and ready to use.

Best if:

• Your Pi failed or was damaged
• You need a drop-in replacement for the main board

Includes:

• Raspberry Pi Zero 2 W, conformal coated with heatsink installed
• 16GB microSD card, preconfigured

🔹 SD Card Only (Firmware)

The 16GB microSD card preloaded with the Peek-a-Hide firmware/software.

Best if:

• Your SD card was lost, corrupted, or damaged
• You want a clean reinstall of the firmware/software

Includes:

• 16GB microSD card, preconfigured with Peek-a-Hide firmware

⚠️ Need just the ribbon cable? You can purchase a replacement directly from Amazon. No need to buy through this listing: 15cm, 15-pin to 22-pin CSI ribbon cable.

💡 What “Fully Configured” Means

Each Raspberry Pi unit ships with:

• Peek-a-Hide firmware/software preloaded on the microSD card
• Silicone conformal coating applied to PCB surfaces for moisture and heat resistance
• Low-profile heatsink installed on the CPU
• Camera ribbon connected and tested when purchasing the Pi + Camera option

These are not bare boards. They are assembled, treated, and tested the same way as a full Peek-a-Hide unit.

💡 What “Fully Configured” Means

Each Raspberry Pi unit ships with:

• Peek-a-Hide firmware/software preloaded on the microSD card
• Silicone conformal coating applied to PCB surfaces for moisture and heat resistance
• Low-profile heatsink installed on the CPU
• Camera ribbon connected and tested when purchasing the Pi + Camera option

These are not bare boards. They are assembled, treated, and tested the same way as a full Peek-a-Hide unit.

🔧 Compatibility

These replacement components are designed for Peek-a-Hide hides sold by this shop.

The Raspberry Pi Zero 2 W and camera module use standard form factors, but firmware/software and setup instructions are tailored specifically to the Peek-a-Hide system. We cannot guarantee compatibility with third-party hides or modified setups.

📋 What’s Not Included

• 3D-printed hide
• Micro USB power cable
• USB charger block, 5V 2A or higher recommended

If you need a full replacement unit including the hide, please see our main Peek-a-Hide listing.

🌐 Network Setup Responsibility

This device connects to your home WiFi network.

You are responsible for:

• Configuring your router
• Entering WiFi credentials
• Managing firewall or port settings if applicable
• Ensuring your internet connection supports video streaming

Because routers and ISP configurations vary widely, we cannot provide router-specific technical support. Basic setup instructions are included.

🌡 Designed for Reptile Enclosures

Typical reptile enclosures operate between:

• 55–70% humidity
• 80–92°F warm zones

To increase durability in these conditions:

• PCB surfaces are treated with silicone conformal coating for flexible, moisture- and heat-resistant corrosion protection.
• A low-profile heatsink is installed on the CPU.
• Camera lens is protected behind a recessed polycarbonate window.

Even with these protections, electronics operating in elevated humidity environments may experience reduced lifespan compared to dry indoor conditions.

🔒 Product Use & Liability Notice

This is a hobbyist monitoring device and is not intended for:

• Veterinary or medical use
• Life-safety monitoring
• Security system replacement

The seller is not responsible for:

• Network configuration issues
• Router compatibility
• Internet outages
• Damage caused by direct misting, water exposure, or misuse

Electronics must not be directly sprayed with water or submerged. Buyer assumes responsibility for proper placement and safe operation inside their enclosure.

🛠 30-Day Limited Hardware Warranty

We stand behind the quality of our assembly and testing.

Covers:

• Hardware defects
• Assembly faults
• Dead-on-arrival components

Does not cover:

• Water damage
• Improper setup
• User modification
• Firmware alterations
• Physical damage after delivery
• Corrosion caused by excessive humidity or enclosure conditions outside normal ranges

Warranty period: 30 days from delivery date.

If an issue occurs, contact us with:

• Order number
• Description of problem
• Photo or short video if applicable

We may offer repair, replacement component, or replacement unit at our discretion. Buyer is responsible for return shipping unless product is dead on arrival.

❗ Important Notes

• Do not place electronics directly above water bowls.
• Do not mist electronics directly.
• Intended for indoor reptile enclosures only.
• Not waterproof.
• SD card firmware is specific to the Peek-a-Hide system and may not be suited for other projects.

📋 Policies & Purchase Agreement

Before purchasing, please review our full policies on our website, which include:

• Privacy Policy
• Terms of Service
• Returns & Refunds
• Warranty & Liability

By completing a purchase, you acknowledge that you have read and agree to these policies, including the 30-day limited hardware warranty terms, return eligibility conditions, and product use and liability disclaimer.